ProjectClue.com WhatsApp or Call Us

projectclue whatsapp icon07030248044

Project Topic:

The design and implementation of domestic remote control for home appliances

Project Information:

 Format: MS WORD ::   Chapters: 1 - 5  ::   Pages: 84 ::   Attributes: Appendix  ::   4,690 people found this useful

Project Department:

ELECTRICAL ENGINEERING UNDERGRADUATE PROJECT TOPICS, RESEARCH WORKS AND MATERIALS

Project Body:

CHAPTER ONE

INTRODUCTION

The need for a remote control alert system that can control domestic appliances and various lighting points and sockets has often been a concern for users. At times users find it inconvenient and time consuming to go around turning their appliances on or off each time there is power outage or each time they are leaving the house for work. It has also often led to damage of appliances due to the fact that an appliance was not turned off before leaving the house.

 OBJECTIVE OF PROJECT

The Objective of putting up this project, therefore, is to design an equipment that can facilitate a convenient and easy way of controlling our domestic appliances, lighting points and sockets especially in powering them, without always going to appliances physically by ourselves.

This objective will be accomplished using various components which include a Microcontroller (AT89C51) which acts as the backbone of the project together with other components.

JUSTIFICATION OF PROJECT

The ease of putting our appliances, lighting points and sockets on or off has made it necessary to develop this system in order to control our appliances, lighting points and sockets from a central point using a remote control. The issues of always forgetting our appliances ON when leaving the house has often caused fire outbreak and explosion in homes and this is another reason that led to designing and construction of this project.

SCOPE OF DIAGRAMS IN PROJECT

In this project report, the diagrams will range from simple block diagrams to complex circuit diagrams which will comprise mostly of common electrical and electronics symbols. Some of the diagrams that will feature in this report will be used as the main block on which certain parameters will be explained upon. Relevant electronic components will also be shown and described.

This project report will also contain an outline of the circuit diagram as it is seen physically. The package design diagram will be included showing the width, height in millimeter (mm).

PROJECT  REPORT ORGANIZATION

Chapter 1 serves as the introductory chapter where I try to relay the concept and acceptable reasons why the project should be implemented for the intending user of the work. Thus, showing the block diagram of the design and a scope of diagram for the entire project design.

Chapter 2 deals with the literature review where it will be discussing the origin of this project design. In the origin of the project, we will be looking at what brings about the three phase selector in our day to day activity and how the idea of designing this project comes about.

A description of the Project is also given where the 2 sections of the project are discussed and the various components contained in the sections also mentioned.The use and importance of this project design will also be mentioned here. It will be looking at the best place where this project design can be use and where it cannot.  This chapter will also make room for adding additional information that will help in the actualization of this project design.

Chapter 3 treats the methodology of this project design. It comprises of the information gathering; the source of the materials used in designing and writing the project report, data analysis; the components and devices used in the course of designing this project will be analysis to know their basic means of operation and how they will help in putting up this design, system design approach; the possible way to tackled the project design from scratch, bottom-up; it will treat how the practical detail was gotten before considering about the general principle of the system design, choice of design system; it focuses on why the project design was done using a microcontroller rather than using only digital logic, and also the data flow arrangement and system flow chart.

In chapter 4, the detail design work will be presented. It will include the schematic of the design of the various sections of the design and the source code (in C language) used in programming the microcontroller.

Chapter 5 will be discussing the system testing, Expected results, and Performance evaluation.

Summary and conclusion of the design will be presented in Chapter 6. It will be looking at the problems encountered in designing the project and possible solutions to them. From the problems and solutions of this work, the suggestion for further improvement will be stated.

 

         

Get the complete project »


Instant Share On Social Media:


Can't find what you are looking for?
Call (+234) 07030248044.

OTHER SIMILAR ELECTRICAL ENGINEERING PROJECTS AND MATERIALS

CONSTRUCTION OF A LIGHT SENSITIVE ALARM

 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 37 ::   Attributes: Abstract  ::   9096 engagements

CHAPTER ONE INTRODUCTION The light sensitive alarm is an electronic circuit that detects a sudden shadow falling on the light sensor and sounds the bleeper. When this happens, the circuit will respo...Continue reading »

CONSTRUCTION OF A MOBILE REFRIGERATOR FRIDGE

 Format: MS WORD ::   Chapters: 1 - 5  ::   Pages: 34 ::   Attributes: Abstract, Table Of Content  ::   4846 engagements

ABSTRACT This write up focuses attention on a detailed report and account on the process of construction and formulation of plan for the actual and physical realization of the construction of the pro...Continue reading »

DESIGN AND CONSTRUCTION OF A MODERN NAIL GASKET MACHINE

 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 41 ::   Attributes: Abstract, Table Of Content  ::   3903 engagements

ABSTRACT The design and fabrication of a reciprocating nail gasket is a new innovation in technology. The one in existence is manually operated. In which a punch that is adjacent to a die is mounted ...Continue reading »

DESIGN AND IMPLEMENTATION OF A SMART DEVICE THAT COUNTS THE NUMBER OF PEOPLE INSIDE A CONFERENCE HALL; AND PREVENTS PEOPLE FROM ENTERING ONCE THE ROOM HAS REACHED ITS CAPACITY.

 Format: MS WORD ::   Chapters: 1 - 5  ::   Pages: 34 ::   Attributes: Appendix  ::   6356 engagements

CHAPTER ONE 1.0 INTRODUCTION The industrial batch counter is an electronic and electrical device that handles the counting and controls the flow of individuals using an automated slide door that al...Continue reading »

DESIGN OF AN AUTOMATIC BATTERY CHARGER

 Format: MS WORD ::   Chapters: N/A ::   Pages: 38 ::   Attributes: Questionnaire, Data Analysis  ::   7392 engagements

CHAPTER ONE Introduction While most modern electrical appliances receive their power directly from the utility grid, a growing number of everyday devices require electrical power from batteries in o...Continue reading »

FABRICATION OF A POLYTHIENE BAG SEALING AND CUTTING MACHINE

 Format: MS WORD ::   Chapters: 1 - 5  ::   Pages: 37 ::   Attributes: Abstract, Table Of Content  ::   3886 engagements

ABSTRACT This machine is meant for sealing and cutting of nylon bag of different sizes. This machine is operated with electrical system. This machine can cut and seal nylon of different sizes. It al...Continue reading »

What are looking for today?

WHAT OUR CUSTOMERS ARE SAYING:
  • 1. Abubakar Sani from Nigerian Investment Promotion Commission said "I had a wonderful experience using ProjectClue, they delivered not only on time, but the content had good quality. I recommend ProjectClue for any project research work.".
    Rating: Excellent
  • 2. Ogunniran Olawale from Ekiti state university said "Projectclue is really safe and reliable Quick access to project works Nice customer service Fast delivery of request Recommend this toy fellow students ".
    Rating: Excellent
  • 3. Fahat Nasir from isa kaita college of education dutsinma said "Fish farming a solution unemployment ".
    Rating: Very Good
  • 4. Ajimbi Oluwarotimi from Theology school osun said "Good ".
    Rating: Very Good
  • 5. Clement Abdullahi Ogiji from National Open University of Nigeria said "I am a living witness and have recommended project clue to a lot of students, so far none have been disappointed, very reliable and, trustworthy and dependable".
    Rating: Excellent
  • 6. Jhuee from Sultan national high school said "Good quality. I recommend project clue for any project research work.".
    Rating: Excellent